Engineering Experience
Aug 23 to Otc 2024
University of Houston
-
Designed and integrated high-speed RF modules (LNA, Mixer, Bias T, TCXO) for advanced biomedical rehabilitation systems—including wearable exoskeletons and gait-monitoring devices—enabling real-time signal acquisition with >95% data integrity.
-
Conducted PCB layout optimization and EMC design using ADS, HFSS, and Altium, reducing prototype debugging time by 20% and enhancing EMI immunity in clinical environments.
-
Authored over 10 comprehensive documentation packages (test procedures, design specifications, compliance reports), accelerating regulatory submission processes and reducing review cycle times by 25%.
-
Collaborated with multidisciplinary teams across biomedical and electrical domains to co-develop signal processing pipelines, improving sensor latency by 18% and lowering system cost by integrating low-power RF solutions.
2021 - 2023
Global Tele Communications
RF Design Engineer
-
Led end-to-end RF front-end module development for transceivers operating across HF, VHF, UHF, and SHF bands, supporting military-grade and commercial communication systems with up to 99.8% signal reliability.
-
Designed and validated LNAs, IF amplifiers, mixers, VCOs, PLLs, and high-power amplifiers (0.5W–1.5KW), increasing coverage range by 35% while maintaining spectral efficiency.
-
Spearheaded the simulation of circuits using Cadence and Keysight ADS for GaN and SiGe technologies, accelerating prototyping cycles by 30% through first-pass design success.
-
Conducted load-pull, IP3, and noise figure testing to ensure EMI/EMC compliance, resulting in 15% production yield improvement and reducing field failure rate by 18%.
-
Diagnosed and resolved RF anomalies via Smith Chart analysis, impedance matching, and root cause analysis, cutting signal distortion by 25% across deployed systems.
2021 - 2022
Silicon Grand
Electronic - Internship
-
Designed a low-power RF emitter with integrated waveguide and band-pass filter for a radar imaging system operating at 319.93 THz, ensuring high spectral resolution and minimal signal loss, which enhanced power efficiency for extended field deployment in harsh environments
-
Developed GPS-disciplined oscillators (GPSDO).
2018 - 2019
Global Green Tech
Electronic - Technician
-
Lab Bench Power Supply - SMPS Power Supply’s EMI, EMC Testing
Education
2023 - Current
Master's in Electrical and Computer Engineering | University of Houston
Major in Electromagnetics
Course Work
-
RF & Microwave Electronics
-
CMOS Analog Integrated Circuits
-
Microwave Engineering
-
Antenna Engineering
-
Intermediate Electromagnetics
-
Advanced Telecommunications Engineering
-
Inverse Problems
Overall GPA 3.5
2018 - 2022
Bachelor's in Electronics and Communication Engineering | Kalinga University
Raipur, Chhattisgarh, India
Skills & Expertise
Circuit Design & RF Modules:
Transceivers, Power Amplifiers, LNAs, IF Amplifiers, Mixers, VCOs, PLLs, Bias T, RF Switching, LPF, BPF, HPF, Tuners, Attenuators, Antennas, SAW/BAW Duplexers, High-Q RF Filters, Impedance Transformation, Matching Circuits, Passive RLC & Resonant Circuits, Noise, Linearity, Bandwidth, Stability, High-Directivity Couplers, Splitters
Test & Equipment:
Lab Debugging, Root Cause Analysis, Vector Network Analyzers, Spectrum Analyzers, Oscilloscopes, Signal Generators, RF Power Meters, SWR Meters, Communication Service Monitors, RF Probe Stations, Noise Figure Analyzers, Load-Pull Tuners, Digital Receivers, SINAD Measurements, Digital Multimeters, Software-Defined Radios, Soldering
RF Testing & Characterization:
Smith Chart Analysis, S-Parameters, Impedance Matching, Intermodulation Distortion (IMD), IP2/IP3, Noise Figure, Automatic Gain Control (AGC), Frequency Conversion, Linearity, Load-Pull, Calibration, EMI/EMC Testing
Simulation, Modeling & Software, Programming
Cadence Virtuoso, Altium, LTspice, ANSYS HFSS, Keysight ADS, MATLAB, Python, C, MS Office (Excel, Word, PowerPoint, Outlook)
Protocols & Standards:
AM/FM/SSB, QAM, MSK/FSK, OQPSK, OOK/ASK, 2G/3G/4G/5G/LTE, WiFi, GPS, Bluetooth, I2C, SPI, CAN, RS232
Technical Documentation:
Design Specifications, Test Procedures scripting, Compliance Reports, Datasheets, Bills of Material (BOM), User Manuals
Additional Technical & Soft Skills:
Advanced Troubleshooting, Analytical Thinking, Problem Solving, Time Management, Innovation, Continuous Improvement, Regulatory & Standards Compliance, Customer Communication, Technical Presentations